The Breanna sleevecap was designed to be adaptable into different types of sleeves and garments. As a result, the sleevecap alone has 20 options to control its shape. Whereas that may seem a bit overwhelming at first, understanding how the sleevecap is drafted makes it easy to understand what all the individual options do.
The bounding box of the sleevecap is a rectangle that is as wide as the sleeve, and as high as the sleevecap. Inside this box, we will construct our sleevecap later.
The image above shows a sleevecap, starting at point 1, then going up until point 4, and then down again to point 2.
In our example, the front of the sleevecap is on the right hand side. But how would you know?
While patterns typically have an indication that shows which side is which (a single notch means the front, whereas a double notch means the back), you can also recognize the front side of a sleevecap because it is more curved. The backside of the sleevecap will also be curved, but it's a flatter curve. That's because the human shoulder is more pronounced and curved on the front of the body, thus the sleevecap is more curved there to fit the shoulder.
The width of the sleevecap (and thus the width of the sleeve at the bottom of the armhole) is equal to the distance between points 1 and 2. That distance depends on the measurements of the model, the amount of ease, the cut of the garment and so on. For our sleevecap, all we need to know is that we start with a given width. And while that width can be influenced by other factors, we can not influence it by any of the sleevecap options.
The height of the sleevecap is equal to the distance between points 3 and 4. The exact height is a trade-off between the measurments of the model, options, ease, sleevecap ease, and the fact that the sleeve ultimately has to fit the armhole. So the height may vary, and we don't control the exact value. But there are two options that control the shape of our sleevecap:
In other words, point 4 can be made higher and lower and, perhaps less intutitively, it can also be changed to lie more to the right or the left, rather than smack in the middle as in our example.
With points 1, 2, 3, and 4 in place, we have a box to draw our sleevecap in. Now it's time to map out our inflection points. These are points 5 and 6 on our drawing, and their placement is determined by the following 4 options:
As you see in our example, these points do not always lie on our sleevecap line. Instead, they are instrumental in creating the points that always lie on the sleevecap: the anchor points.
Ultimately, our sleevecap will be the combination of 5 curves. In addition to points 1 and 2, the four anchor points that are marked in orange in our example will be the start/finish of those curves.
The points are offset perpendicular from the middle of a line between the two anchor points surrounding them. The offset for each point is controlled by these 4 options:
We've divided our sleevecap into 4 quarters. We start at the front (the right in our example) with quarter 1, and make our way to the back to end with quarter 4.
Like the offset option, the last options to determine the shape of our sleevecap will just repeat so you can control each quarter individually.
We now have all the start and end points to draw the 5 curves that will make up our sleevecaps. What we're missing are the control points (see our info on Bézier curves to learn more about how curves are constructed). These are determined by the so-called spread.
For each of the anchor points (the ones marked in orange, not points 1 and 2) there is an option to control the spread upwards, and downwards:
Attentive readers will have noticed that point 4 is not an anchor point. In other words, there is no guarantee that it will lie on the sleevecap line. Which also means that the upwards spread in quarters 2 and 3 will influence the height of the sleevecap. Reduce the upwards spread, and the curve will dip below point 4. Increase it and the curve will rise above it.
While the sleevecap in Breanna (and all patterns that extend Breanna) have a lot of options, understanding how the sleevecap is constructed can help you design the exact sleevecap shape you want. To do so:
What's important to remember is that you're only ever controlling the shape of the sleevecap. Whatever shape you design, it will be fitted to the armhole, meaning that its size can and will be adapted to make sure the sleeve fits the armscye. However, the shape you design will always be respected.